We are distributor of Beele/CSD in Vietnam supplying penetration system for cables and pipes.

3. CSD SLIDE

Up until then, your choices were limited to either cumbersome block systems or messy casting compounds. Once Beele/CSD was introduced, it was clear that this was unlike any other system in history. Beele/CSD offered unprecedented fire protection, flexibility, and installed cost savings - all without the use of metal parts, casting compounds or mineral wool.

 

Cable/Pipe Penetration Products:

 

  • RISE: RISE® cable/pipe penetrations have been the product of choice for shipyards around the world for almost 20 years. The system is comprised of just two simple components - FRR/LEHF rubber for insert sleeves, filler sleeves and wrap and FIWA® Sealant, which provide the utmost in fire, water and gas protection.

rise-cable-1 rise-cable-2 rise-cable-3 rise-pipe-1

 

  • RISE/NOFIRNO: RISE/NOFIRNO cable/pipe penetrations are the latest introduction to the CSD/Beele family of passive fire safety products. Based on revolutionary new NOFIRNO® technology, RISE/NOFIRNO offers ultimate flexibility for sealing cable/pipe penetrations. The system is comprised of just two simple components - rubber insert sleeves and NOFIRNO® Sealant, which provide the utmost in fire, water and gas protection.

nofirno-pipe-1 nofirno-pipe-2 nofirno-pipe-3

 

  • RISE Ultra: RISE Ultra Crusher® system has revolutionized the sealing of plastic pipe penetrations. The system is comprised of just two simple components - a RISE/ULTRA Crusher® and NOFIRNO® Sealant. The system provides fire protection to A-60 and is also watertight rated.

rise-ultra-1 rise-ultra-2 rise-ultra-3

 

  • SLIPSIL: SLIPSIL® Sealing Plugs are the latest generation of the CSD Sealing Plugs, which have been used in shipyards worldwide for over 20 years. SLIPSIL® Plugs are made from high quality NOFIRNO® Rubber and are approved for all types of metallic and even plastic pipes!

slipsil-1 slipsil-2 slipsil-3

 

  • ACTIFOAM: ACTIFOAM® Temporary Seals for cable penetrations protect your installation while under construction or renovation. Fires can and do start during construction, before the cable transits can be packed. If the cables ignite, fire can spread rapidly throughout your vessel or rig, often with devastating consequences. ACTIFOAM® Temporary Seals prevent this problem. Simply pack the transit opening with ACTIFOAM® pre-slit pads and you are protected against the spread of fire. Material is durable and reusable from project to project.

actifoam-1 actifoam-2 actifoam-3

 

  • RISWAT: The RISWAT® penetration system is the leading choice for watertight, gas-tight penetrations that require no fire protection. This cost-effective system is simple to use with cable and single or multi-pipe penetrations. The system is comprised of just two components - RISWAT® Thermoplastic sleeves and DRIFIL® Sealant.

riswat-1 riswat-2 riswat-3

 

  • DYNATITE: The DYNATITE® High Pressure Sealing System was developed for vulnerable areas that may experience severe instantaneous pressure caused by explosions, flooding or other disasters. The high-tech design of DYNATITE® actually allows the system to get tighter as the pressure increases. DYNATITE® was specially developed for application in columns in semi-submersible offshore rigs, following incidents where traditional cable transit systems suffered catastrophic failure under high pressure. There's nothing else like DYNATITE® to protect your critical systems and areas.

dynatite-1 dynatite-2 dynatite-3

 

Contact us for details. Hand phone 09 88 57 43 47, email This email address is being protected from spambots. You need JavaScript enabled to view it. 

 

CSD 1 CSD 8 CSD 9

 

 

CSD 2 CSD 11

  

 

CSD 4 CSD 5 CSD 10

  

 

CSD 6 CSD 7  

 

CSD 3  CSD 13  CSD 15

  

CSD 14CSD 12

We are a distributor of Workitalia in Vietnam. The main equipments as follows:

HYDRAULIC PUNCHING TOOLS CEMBRE:

CRIMPING HEAD AND HYDRAULIC PUMPS CEMBRE:

 

BATTERY HYDRAULIC CUTTING TOOLS CEMBRE:

BATTERY HYDRAULIC CRIMPING TOOLS CEMBRE:

 

MANUAL HYDRAULIC CUTTING TOOLS CEMBRE:

MANUAL HYDRAULIC CRIMPING TOOLS CEMBRE:

 

Apator

 

Tube CT Description   Application
 Tube current transformers(round primary conductor)
The current  transformers are family of switchgear devices that allow measurement of large currents and voltage using meters with smaller ranges. Current transformers with special hole with a diameter of 21 mm or 23 mm can be mounted on the cable. In addition, there is also a copper tube tht allows installation of the current transformer on the cable of smaller diameter.   Current transformer for round conductor ø 21 mm, designed for ARS 00/100mm, ARS 00/100 mm pro, ARS 00, ARS 00 pro fuse switch disconnectors.

Apator

 

ASR pro Description   Thông số kỹ thuật Material   Feature
 ARS pro vertical fuse switch disconnectors
ARS pro vertical fuse switch disconnectors are designed for distribution of electricity and protection against short cir­cuits and overloads in three phase alternative current circuits. ARS pro fuse switch disconnectors are dedicated for applications which require reliability and safety like low voltage distribution boards installed in transformer substations, industrial low voltage distribution boards and cable cabinets.   ARS 00/100mm pro In=160 A, Un=690 V
ARS 00 pro In=160 A, Un=690 V
ARS 2 pro In=400 A, Un=690 V
ARS 3 pro In=630 A, Un=690 V
ARS 630 kVA pro In=910 A, Un=400 V
RWS 1250 A pro In=1250 A, Un=400 V
ARS 1250 A pro In=1250 A, Un=400 V
Lateral bus bar terminal
Electronic fuse monitoring module
ARS fuse switch disconnectors are made of fibre glass strengthened, thermoplastic polyamides with halogen free flame retardant added. Added flame retardant provides V2 flammability class according to IEC 60695-11-10. Such thermoplastics have longer self-extinguish time after ignition source is removed than V0 class thermoplastics. Also dripping of non fla­ming parts of plastic is allowed.  
  • parallelly moving, double contact system,
  • two arc chutes installed in each pole 2 are equipped with metal plates that stretch and further split electric arc during switching off of the circuit,
  • main base of fuse switch disconnector ARS pro is made of halogen free, fibre glass strengthened, self extingu­ishing, thermoset polyester of V0 flammability class,
  • other plastic parts of fuse switch disconnectors ARS pro are made of fibre glass strengthened, thermoplastic polyamides with halogen free flame retardant added; thanks to such addition the highest flammability class – V0 was achieved,
  • silver plated contacts provide low power loss and high conductivity,
  • for installation on to 185 mm busbar system,
  • triple pole switching (three poles at the same time) or single pole switching 

 

Apator

 

RA and RAB Description   Technical data Standard   Feature
 RAB with fuses
RA switch disconnectors and RAB switch disconnectors fuses are designed for distribution of electricity, making and breaking currents and protection of electrical equipment against shortcircuits and overloads in three phase alternative current circuits.   RAB 000, In=100 A
RAB 00, In=160 A
RAB 1, In=250 A
RAB 2, In=400 A
RAB 3, In=630 A
RA 100, In=100 A
RA 160, In=160 A
RA 250, In=250 A
RA 400, In=400 A
RA 630, In=630 A
RA 1250, In1250 A
Change-over switches I-0-II
Replacement for 400 a switch disconnector - RA 400/O
RIN switch disconnectors
RA are designed according to IEC/EN 60947-1, IEC/EN 60947-3 and can be used as main switch disconnector in distribution boards, switch disconnector, and switch disconnector for motor control and protection.   - safety of service and easy installation
- self-extinguishing thermoplastics (V0 flammability class)
- silver plated parts of current circuits
- self-tightening and self-cleaning contacts
- high electrical and mechanical endurance
- high short-circuit making and breaking capacity
- double, safe clearance between open contacts
- complete isolation of fuse links in „off” position
- manually operated drive (spring powered)
- wide range of accesories

 

Apator

 

RBK pro Description   Technical data Material   Feature
 RBK pro fuse disconnectors
RBK pro fuse switch disconnectors are designed for distribution of electricity and protection against short cir­cuits and overloads in three phase alternative current circuits. RBK pro fuse switch disconnectors are dedicated for applications which require reliability and safety like industrial low voltage distribution boards and cable cabinets.   RBK 00 pro In=160 A, Un=690
RBK 00 pro-V120 In=160 A, Un=690 V
RBK 1 pro In=250 A, Un=690 V
RBK 2 pro In=400 A, Un=690 V
RBK 3 In=630 A, Un=690 V
RBK 00-XT
RBK pro meet technical requirements of polish and other european electricity boards and are conforming to PN-EN 60947-1, PN-EN 60947-3,IEC 60947-1, IEC 60947-3 standards.
Fuse switch disconnectors RBK pro are made of plastic with the highest V0 flammability class according to IEC 60695-11-10. Fuse switch disconnectors made from such thermo­plastics self-extinguish in specified time after ignition source is removed. Also dripping of flaming parts of plastic does not occur.
 

- Triple pole switching,
- For installation on:
     - Mounting plate,
     - Double DIN rail with spacing of 125 mm or 150 mm,
     - On to 60 mm busbar system, top or bottom cable terminals,
- Arc chutes with steel deionization plates over top contacts,
- Possible cable connection: S-bridge clamp, M8 screw and V-

  shape clamp
- Possible sealing of a fuse switch disconnector,
- User can replace the fuse link while it is still hot after it  has

   operated, without touching it,

- Measuring holes to monitoring of the fuse state.

Ma tít trám ống gió Design Polymerics/USA

Chúng tôi là đại diện tại Việt Nam của hãng SENSORLINK - USA chuyên về các thiết bị đo lường trung thế.

sensorlink product

Giá: Liên hệ

Page 1 of 5

HOP THIEN COMPANY LIMITED

Address   : Ground Floor, Rosana Tower, No. 60 Nguyen Dinh Chieu St., Da Kao Ward, Dist. 1, Ho Chi Minh City, Vietnam
Tel

: +84 28 22 00 21 24 ; 09 88 57 43 47 (Mr. Trieu)

                                        09 79 87 84 50 (Mr. Khiet)            

Fax : +84 28 22 20 22 01
Email : thientrieu@hopthien.com
Website : http://www.hopthien.com


ngoxuantrieu

ngoxuantrieu

Joomla Templates - by Joomlage.com